Abstract
Elastomeric foams based on 60/40 EVA/NR blend nanocomposite were prepared by melt mixing EVA, NR and clay (5 phr) in an internal mixer, and later foamed with azodicarbonamide through compression molding. Epoxidized natural rubber (ENR) with epoxide content of 25 mole% was used as a compatibilizer to improve interfacial adhesion between EVA and NR. The addition effect of ENR concentration on the blending and properties of EVA/NR blend nanocomposite foams was studied. XRD and TEM results showed that the clay in the EVA/NR blends was intercalated and locally existed in the NR phase as well as at the interface between EVA and NR. The EVA/NR blend nanocomposites showed dispersed NR domains in continuous EVA phase. The addition of ENR into EVA/NR blend nanocomposites reduced the size of the dispersed NR phase, indicating that the blend miscibility was improved. Mechanistic model was proposed for the miscibility improvement of a two-phase structure of EVA/NR blend nanocomposite in the presence of ENR and clay dispersion. However, the improved blend morphology did not significantly affect the cell structure of EVA/NR blend nanocomposites. The observation of cell structure of EVA/NR blend nanocomposites suggested that the increased addition of ENR caused a little increase in cell density, and had no influence on cell size. Furthermore, with increasing addition level of ENR in the blend nanocomposite foams, the foam density slowly decreased, whereas the specific tensile strength slightly increased. The elastomeric recovery of blend nanocomposite foams decreased with increasing ENR content. The thermal conductivity of EVA/NR blend nanocomposite foams also decreased with more addition of ENR, which had beneficial result in improving thermal insulation property.
References
Arroyo, M., Lopez-Manchado, M. A. and Herrero, B., “Organo-Montmorillonite as Substitute of Carbon Black in Natural Rubber Compounds”, Polymer, 44, 2447–2453 (2003) 10.1016/S0032-3861(03)00090-9Search in Google Scholar
Fang, Z., Harrats, C., Moussaif, N. and Groeninckx, G., “Location of a Nanoclay at the Interface in an Immiscible Poly(∊-caprolactone)/Poly(ethylene oxide) Blend and its Effect on the Compatibility of the Components”, J. Appl. Polym. Sci., 106, 3125–3135 (2007) 10.1002/app.26331Search in Google Scholar
Fyodor, Dr., Shutov, A., “Chapter 3 Cellular Structure and Properties of Foamed Polymers”, in Handbook of Polymeric Foams and Foam Technology, Klemper, D., Frish, K. C., (Eds.), Hanser, Munich, p. 39–46 (1991)Search in Google Scholar
Giannelis, E. P., “Polymer-layered Silicate Nanocomposites: Synthesis, Properties and Applications”, Appl. Organomet. Chem., 12, 675–680 (1998) 10.1002/(SICI)1099-0739(199810/11)12:10/11<675::AID-AOC779>3.0.CO;2-VSearch in Google Scholar
Gong, P., Ohshima, M., “Effect of Interfacial Tension on the Cell Structure of Poly(methyl methacrylate)/Bisphenol A Polycarbonate Blends Foamed with CO2”, J. Appl. Polym. Sci., 131, 39228 (2013) 10.1002/app.39228Search in Google Scholar
Istrate, O. M., Gunning, M. A., Higginbotham, C. L. and Chen, B., “Structure–Property Relationships of Polymer Blend/Clay Nanocomposites: Compatibilized and Noncompatibilized Polystyrene/Propylene/Clay”, J. Polym. Sci., Part B: Polym. Phys., 50, 431–441 (2011) 10.1002/polb.23018Search in Google Scholar
Joly, S., Garnaud, G., Ollitrault, R. and Bokobza, L., “Organically Modified Layered Silicates as Reinforcing Fillers for Natural Rubber”, Chem. Mater., 14, 4202–4208 (2002) 10.1021/cm020093eSearch in Google Scholar
Kim, M. S., Park, C. C., Chowdhury, S. R. and Kim, G. H., “Physical Properties of Ethylene Vinyl Acetate Copolymer (EVA)/Natural Rubber (NR) Blend based Foam”, J. Appl. Polym. Sci., 94, 2212–2216 (2004) 10.1002/app.21174Search in Google Scholar
Kim, S. H., Lee, M. C., Kim, H. D., Park, H. C., Jeong, H. M., Yoon, K. S. and Kim, B. K., “Nanoclay Reinforced Rigid Polyurethane Foams”, J. Appl. Polym. Sci., 117, 1992–1997 (2010) 10.1002/app.32116Search in Google Scholar
Kinkelaar, M. R., Thompson, A. M. and Krisher, D. P., U.S. Patent 6051622 A (2000)Search in Google Scholar
Kumar, V., Suh, N. P., “A Process for Making Microcellular Thermoplastic Parts”, Polym. Eng. Sci., 30, 1323–1329 (1990) 10.1002/pen.760302010Search in Google Scholar
Lopattananon, N., Julyanon, J., Masa, A., Kaesaman, A., Thongpin, C. and Sakai, T., “The Role of Nanofillers on (Natural Rubber)/(Ethylene Vinyl Acetate)/Clay Nanocomposite in Blending and Foaming”, J. Vinyl. Addit. Tech., 21, 134–146 (2015) 10.1002/vnl.21368Search in Google Scholar
Lopattananon, N., Tanglakwaraskul, S., Kaesaman, A., Seadan, M. and Sakai, T., “Effect of Nanoclay Addition on Morphology and Elastomeric Properties of Dynamically Vulcanized Natural Rubber/Polypropylene Nanocomposites”, Int. Polym. Proc., 29, 332–341 (2014a) 10.3139/217.2935Search in Google Scholar
Lopattananon, N., Wangpradit, N., Nakason, C. and Kaesaman, A., “Effect of Rubber Composition on Foaming and Properties of EVA/NR/PP Thermoplastic Vulcanisates (TPVs)”, J. Rubb. Res., 17, 80–95 (2014b)Search in Google Scholar
Mao, Y., Qi, R., “Preparation of Polyethylene–Octene Elastomer Foams by Compression Molding”, J. Appl. Polym. Sci., 109, 3249–3255 (2008) 10.1002/app.28415Search in Google Scholar
Masa, A., Saito, H., Sakai, T., Kaesaman, A. and Lopattananon, N., “Morphological Evolution and Mechanical Property Enhancement of Natural Rubber/Polypropylene Blend Through Compatibilization by Nanoclay”, J. Appl. Polym. Sci., 134, 44574 (2017) 10.1002/app.44574Search in Google Scholar
Masa, A., Iimori, S., Saito, R., Saito, H., Sakai, T., Kaesaman, A. and Lopattananon, N., “Strain-Induced Crystallization Behavior of Phenolic Resin Crosslinked Natural Rubber/Clay Nanocomposites”, J. Appl. Polym. Sci., 132, 42580 (2015) 10.1002/app.42580Search in Google Scholar
Messersmith, P. B., Giannelis, E. P., “Synthesis and Barrier Properties of Poly(∊-caprolactone)-Layered Silicate Nanocomposites”, J. Polym. Sci., Part A: Polym. Chem., 33, 1047–1057 (1995) 10.1002/pola.1995.080330707Search in Google Scholar
Mitsunaga, M., Ito, Y., Ray, S. S., Okamoto, M. and Hironaka, K., “Intercalated Polycarbonate/Clay Nanocomposites: Nanostructure Control and Foam Processing”, Macromol. Mater. Eng., 288, 534–548 (2003) 10.1002/mame.200300097Search in Google Scholar
Nam, P. H., Maiti, P., Okamoto, M., Kotaka, T., Nakayama, T., Takada, M. and Ohs, M., “Foam Processing and Cellular Structure of Polypropylene/Clay Nanocomposites”, Polym. Eng. Sci., 42, 1907–1918 (2002) 10.1002/pen.11083Search in Google Scholar
Park, K. W., Chowdhury, S. R., Park, C. C. and Kim, G. H., “Effect of Dispersion State of Organoclay on Cellular Foam Structure and Mechanical Properties of Ethylene Vinyl Acetate Copolymer/Ethylene-1-Butenecopolymer/Organoclay Nanocomposite Foams”, J. Appl. Polym. Sci., 104, 3879–3885 (2007) 10.1002/app.26003Search in Google Scholar
Park, K. W., Kim, G. H. and Chowdhury, S. R., “Improvement of Compression Set Property of Ethylene Vinyl Acetate Copolymer/Ethylene-1-Butene Copolymer/Organoclay Nanocomposite Foams”, Polym. Eng. Sci., 48, 1183–1190 (2008) 10.1002/pen.21073Search in Google Scholar
Ray, S. S., Pouliot, S., Bousmina, M. and Utracki, L. A., “Role of Organically Modified Layered Silicate as an Active Interfacial Modifier in Immiscible Polystyrene/Polypropylene Blends”, Polymer, 45, 8403–8413 (2004) 10.1016/j.polymer.2004.10.009Search in Google Scholar
Reyes-Labarta, J. A., Olaya, M. M. and Marcilla, A., “DSC Study of Transitions Involved in Thermal Treatment of Foamable Mixtures of PE and EVA Copolymer with Azodicarbonamide”, J. Appl. Polym. Sci., 102, 2015–2025 (2006) 10.1002/app.23969Search in Google Scholar
Ruckdäschel, H., Sandler, J. K. W., Altstädt, V., Rettig, C., Schmalz, H., Abetz, V. and Müller, A. H. E., “Compatibilisation of PPE/SAN Blends by Triblock Terpolymers: Correlation between Block Terpolymer Composition, Morphology and Properties”, Polymer, 47, 2772–2790 (2006) 10.1016/j.polymer.2006.02.064Search in Google Scholar
Shimbo, M., Higashitani, I. and Miyano, Y., “Mechanism of Strength Improvement of Foamed Plastics Having Fine Cell”, J. Cell. Plasts., 43, 157–167 (2007) 10.1177/0021955X06075585Search in Google Scholar
Sombatsompop, N., “Effects of Crosslink Characteristics on Density and Swelling Behaviour of Expanded Natural Rubber Vulcanisates”, Cell. Polym., 17, 63–74 (1998)Search in Google Scholar
Thomas, S., Stephen, R.: Rubber Nanocomposites: Preparation, Properties and Applications, Wiley, Singapore (2010) 10.1002/9780470823477Search in Google Scholar
Wang, Z., Cui, Y. T., Xu, Z. B. and Qu, J., “Hot Water-Promoted Ring-Opening of Epoxides and Aziridines by Water and Other Nucleopliles”, J. Org. Chem., 73, 2270–2274 (2008) 18288864 10.1021/jo702401tSearch in Google Scholar PubMed
Xu, Z. R., Park, H. Y., Kim, H. Y. and Seo, K. H., “Effects of Modified MMT on Mechanical Properties of EVA/MMT Nanocomposites and their Foams”, Macromol. Symp., 264, 18–25 (2008) 10.1002/masy.200850404Search in Google Scholar
Zhai, W., Wang, H., Yu, J., Dong, J. and He, J., “Foaming Behavior of Polypropylene/Polystyrene Blends Enhanced by Improved Interfacial Compatibility”, J. Polym. Sci., Part B: Polym. Phys., 46, 1641–1651 (2008) 10.1002/polb.21498Search in Google Scholar
Zhang, B. S., Zhang, Z. X., Lv, X. F., Lu, B. X. and Xin, Z. X., “Properties of Chlorinated Polyethylene Rubber/Ethylene Vinyl Acetate Copolymer Blend-Based Foam”, Polym. Eng. Sci., 52, 218–224 (2012) 10.1002/pen.22071Search in Google Scholar
© 2018, Carl Hanser Verlag, Munich