Skip to content
BY-NC-ND 3.0 license Open Access Published by De Gruyter Open Access March 1, 2003

Modeling and simulation of free radical polymerization of styrene under semibatch reactor conditions

Silvia Curteanu
From the journal Open Chemistry

Abstract

The first part of this approach is concerned with the elaboration of a radical polymerization model of styrenne, based on a kinetic diagram that includes chemical and thermal initiation, propagation, termination by recombination and chain transfer to the monomer. Furthermore, volume contraction during polymerization is considered, as well as the gel and glass effects. The mathematical formalism that describes the model in terms of moments is explored in detail. The model was then used to predict the changes in monomer conversion and molecular weight after intermediate addition of initiator and monomer. The results of this operation are dependent on the conditions of the reaction mass, quantity, and moment of substance addition. Therefore, the simulations were performed at different times with respect to the gel effect; before, during and after this phenomenon, and also with respect to different temperatures and initiators. Increasing the initiator concentration before the gel effect leads to an earlier appearance of the phenomenon and to a decrease in molecular weight. The ratio $$\bar M_w /\bar M_n $$ reveals a polydispersity index smaller for the intermediate addition of initiator. No significant changes take place during or after the gel effect. If along with the initiator, unreacted monomver (used to dissolve the initiator) enters the reactor, a small dip in conversion is observed. The general conclusion of this paper reveals the intermediate addition of initiator as a method to control polymer properties and to prevent the “dead-end” polymerization of styrene.

[1] D.S. Achilias and C. Kiparissides: “Development of a General Mathematical Framework for Modeling Diffusion-Controled Free Radical Polymerization Reactions”, Macromolecules, Vol. 25, (1992), pp. 3739–3750. http://dx.doi.org/10.1021/ma00040a02110.1021/ma00040a021Search in Google Scholar

[2] R.G. Gilbert, J.F. Anstey, N. Subramanian, M.J. Monteiro: “Emulsion Polymerization as a novel tool in controlled free-radical polymerization”, Polym. Prepr., Vol. 40, (1999), pp. 297–298. Search in Google Scholar

[3] A. Sirohi and K. Ravindranath: “Modeling of Ionic Polymerization Processes: Styrene and Butadiene”, AIChE, Spring 99 Meeting, Houston, 1999. Search in Google Scholar

[4] K.J. Kim: Modeling and Control of Continuous Free Radical Polymerization Reactors, Thesis (PhD), University of Maryland, 1991. Search in Google Scholar

[5] S. Curteanu, V. Bulacovschi, R. Diaconescu: “Modeling of Free Radical Polymerization of Styrene Using a Binary Mixture of Initiarors”, Proc. Rom. Acad., Vol. 3, (2001), pp. 207–213. Search in Google Scholar

[6] S. Curteanu and V. Bulacovschi: “Modeling of Free Radical Polymerization of Styrene Using a Binary Mixture of Initiators and Isothermal Steps of Temperature”, Rev. Roum. Chim., in press. Search in Google Scholar

[7] W.Y. Chiu, G.M. Carratt, D.S. Soong: “A Computer Model for the Gel effect in Free Radical Polymerization”, Macromolecules, Vol. 16, (1983), pp. 348–357. http://dx.doi.org/10.1021/ma00237a00210.1021/ma00237a002Search in Google Scholar

[8] M. Constantinescu, V. Bulacovschi, S. Curteanu: “Free Radical Polymerization of Styrene. Modeling and Simulation”, Bul. Polyt. Inst. Iasi, Tom XLIII (XLVII), 3–4, (1997), pp. 91–103. Search in Google Scholar

[9] G.A. O'Neil, M.B. Wisnudel, J.M. Torkelson: “An Evaluation of Free Volume Approaches to Describe the Gel Effect in Free Radical Polymerization”, Macromolecules, Vol. 31, (1998), pp. 4537–4545. http://dx.doi.org/10.1021/ma971367010.1021/ma9713670Search in Google Scholar

Published Online: 2003-3-1
Published in Print: 2003-3-1

© 2003 Versita Warsaw

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.

Scroll Up Arrow