Abstract
The article presents many numerical studies and experimental research of the drive rubber boot of the joint drive vehicle. Performance requirements have been discussed and the required coefficients of the mathematical model for numerical simulation have been determined. The behavior of living in MSC.MARC environment was examined. In the analysis the following have been used: hyperplastic two-parameter model of the Mooney-Rivlin material, large displacements procedure, safe contact condition, friction on the sides of the boots. 3D numerical model of the joint bootwas analyzed under influence of the forces: tensile, compressive, centrifugal and angular. Numerous results of studies have been presented. An appropriate test stand was built and comparison of the results of the numerical analysis and the results of experimental studies was made. Numerous requests and recommendations for utilitarian character have been presented.
References
[1] Ziobro J., Marciniec A., Projektowanie form wtryskowych do elastomerów, OWPRz Rzeszów 2015, Search in Google Scholar
[2] Fabianski M., Oznaki zuzycia przegubów homokinetycznych, Motofakty, Poland, 28.01.2014, http://www.motofakty.pl/artykul/oznaki-zuzycia-przegubowhomokinetycznych. html. Search in Google Scholar
[3] Ziobro J., Modelowanie matematyczne i symulacja numeryczna formowania wtryskowego elastomeru chloroprenowego z zastosowaniem programu Moldex3D, Tworzywa sztuczne w przemysle, 2012, 5/2012, X-XIV, 6/2012, 32-35. Search in Google Scholar
[4] Gilles T., Automotive Service: Inspection, Maintenance, Repair, 5th ed., Tomson Cengage Learning, Boston, USA, 2016, Chapter 14, 211-214. Search in Google Scholar
[5] Thomas A., Jung M., Collision Repair and Reffinishing: A Foundation Course for Technicians, 2nd ed., Delmar Cengage Learning, New York, USA, 2014, 939-942. Search in Google Scholar
[6] VanGelder T., Fundamentals of Automotive Technology, Jones & Barlett Learning, Burlington, USA, 2014, 734-738. Search in Google Scholar
[7] Ziobro J., Marciniec A., Zastosowanie narzedzi CAx w projektowaniu form wtryskowych, Polimery, 2010, 55, 877-882. 10.14314/polimery.2010.877Search in Google Scholar
[8] Ziobro J., Wieloosiowa analiza naprezen i odkształcen gumy na bazie kauczuku naturalnego, Zeszyty Naukowe Politechniki Rzeszowskiej 288, Mechanika 85 (nr 2/2013), tom XXX, 197- 206. 10.7862/rm.2013.19Search in Google Scholar
[9] Ziobro J., Multiaxial stress and strain analysis of the rubber based on the natural rubber NR. Int. Sci. Conf. PRO-TECH-MA 2013. OWPRz Rzeszów 2013, 81-82 abstract, 258-263 full. Search in Google Scholar
[10] Ziobro J., Analysis of the V- ribbed belt, Int. Sci. Conf. PRO-TECHMA, Herlany, 2012, 464-471. Search in Google Scholar
[11] Norihiro S., Computer-Aided Rubber Product Design, In: Bhowmick A.K et al. (Eds.), Rubber Products Manufacturing Technology, CRC Press, New York, USA, 1994, 503-513. Search in Google Scholar
[12] Silles T., Automotive Chassis: Brakes, Suspension, and Steering, Tomson Cengage Learning, Santa Barbara, USA, 2005, 350- 420. Search in Google Scholar
[13] Allen M., Replacing Front-Drive Axles, Popular Mechanic, New York, USA, 28.03.2006, http://www.popularmechanics.com/cars/howto/ a290/1715877/. Search in Google Scholar
[14] Stobb. J., Seattle Subaru CV Boots and Axle Problems Explained, All Wheel Drive Auto, Kirkland, USA, 15.09.2009, https://allwheeldriveauto.com/seattle-subaru-cv-boots-andaxle- problems-explained/. Search in Google Scholar
©2016 J. Ziobro
This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.