Jump to ContentJump to Main Navigation
Show Summary Details
More options …

Pure and Applied Chemistry

The Scientific Journal of IUPAC

Ed. by Burrows, Hugh / Stohner, Jürgen


IMPACT FACTOR 2018: 2.350
5-year IMPACT FACTOR: 4.037

CiteScore 2018: 4.66

SCImago Journal Rank (SJR) 2018: 1.240
Source Normalized Impact per Paper (SNIP) 2018: 1.826

Online
ISSN
1365-3075
See all formats and pricing
More options …
Volume 86, Issue 4

Issues

ICTAC nomenclature of thermal analysis (IUPAC Recommendations 2014)

Trevor Lever / Peter Haines / Jean Rouquerol / Edward L. Charsley / Paul Van Eckeren / Donald J. Burlett
Published Online: 2014-03-19 | DOI: https://doi.org/10.1515/pac-2012-0609

Abstract

The widespread use of thermal analysis (TA) by scientists as a laboratory technique carries with it a working vocabulary. This document is intended to provide those working in the field with a consistent set of definitions to permit clear and precise communication as well as understanding. Included in the document are the definitions of 13 techniques, 54 terms within the glossary, as well as symbols and units.

Keywords: differential scanning calorimetry; differential thermal analysis; evolved gas analysis; International Confederation for Thermal Analysis and Calorimetry (ICTAC); IUPAC Physical and Biophysical Chemistry Division; sample-controlled thermal analysis; thermal properties; thermodilatometry; thermogravimetry

Article note: Sponsoring body: IUPAC Physical and Biophysical Chemistry Division: see more details on p. 552.

1 Scope

The scope of this document is to provide scientists working in the field of thermal analysis (TA) with a consistent “definitions of terms” that are commonly used within the field to allow precise communication and understanding. Since the scope of the International Confederation for Thermal Analysis and Calorimetry (ICTAC) also covers calorimetry, a further document dealing with this latter part of nomenclature is planned, once a satisfactory international consensus is reached on this matter.

In considering all the matters of nomenclature, the current ICTAC Nomenclature Committee has followed the advice of the late Robert Mackenzie in that

  • terminology should be simple, and

  • names based on particular instruments should be discouraged.

2 Intent

This document acknowledges that nomenclature develops without regulated definition as the field of thermal analysis develops. Some terms used by authors and scientists rapidly become accepted by the scientific community, even if the term is not consistent with past definitions or is not grammatically correct. However, if such a term is widely used and understood, it is reported here.

3 Definition of the field of thermal analysis

Thermal analysis (TA) is the study of the relationship between a sample property and its temperature as the sample is heated or cooled in a controlled manner.

4 Techniques

A technique exists for each property or physical quantity that is measured versus temperature. A summary of some of these are presented below.

5 Terminology and glossary

Note: For all the techniques listed here, the terminology defines the property that is measured, and each definition of a technique may be completed by adding… “as a function of temperature”. For example: dynamic mechanical analysis (DMA), a technique where storage and loss viscoelastic moduli are determined with the help of a periodical stress as a function of temperature.

Note: Each entry listed below is followed by n. or adj. indicating if the term is either a noun or an adjective.

atmosphere, n.

Gaseous environment of the sample, which may be controlled by the instrumentation or generated by the sample.

combined, adj.

Application of two or more techniques to different samples at the same time. This can include thermal and nonthermal analytical techniques. Different from simultaneous.

controlled-rate thermal analysis (CRTA), n.

Sample-controlled method where the feedback used to control the heating is the rate of transformation.

controlled temperature program, n.

Temperature history imposed on the sample during the course of the thermal analysis experiment.

cooling curve, n.

Experimental result of measuring the temperature of the sample as a function of time during cooling. Heating curves are obtained for temperature-time experiments during heating.

derivative, adj.

Pertaining to the 1st derivative (mathematical) of any curve with respect to temperature or time.

dielectric thermal analysis (DEA), n.

Technique where dielectric properties are measured.

differential, adj.

Pertaining to a difference in measured or measurable quantities usually between a sample and a reference or standard material.

differential scanning calorimetry (heat-flow DSC), n.

Technique where the difference between the heat-flow rates into a sample and a reference material is measured.

differential scanning calorimetry (power compensation DSC), n.

Technique where the difference between the electrical powers into a sample and a reference material is measured.

differential thermal analysis (DTA), n.

Technique where the temperature difference between a sample and a reference material is measured.

dynamic, adj.

Indicates, especially in the mechanical analysis of materials, that a parameter changes continuously during the experiment; opposite of static.

dynamic mechanical analysis (DMA), n.

Technique where storage and loss viscoelastic moduli are determined with the help of a periodical stress.

emanation thermal analysis (ETA), n.

Special type of evolved gas analysis (EGA) where the emanation of previously trapped radioactive gas is measured.

evolved gas analysis (EGA), n.

Family of techniques where the nature and/or amount of gas or vapour evolved is determined. The term evolved gas detection (EGD) has also been used where the nature of gas is not determined.

gas flow, n.

Passage of gas from one part of the system to another. The gas may be either inert (carrier gas) or reactive, either introduced into the system or evolving from the sample.

isothermal, adj.

Applied to a technique to indicate that the temperature is maintained constant throughout the experiment

material, n.

The substance which is studied and from which the sample is taken.

micro-, prefix

Prefix used to denote that the technique measures small quantities, either with respect to the amount of sample studied, or with respect to the change in the properties measured. Mathematically, 1 micro = 1 μ = 10–6.

  • Note 1:

    This prefix has been applied to many thermal methods, and the equipment associated with them, for example, microbalance, microreactor, microcalorimeter and also to the technique itself: microthermal, microscopic, and the property studied: microstructural.

  • Note 2:

    The opposite prefix, macro-, is also occasionally used.

modulated, adj.

Indicates that a parameter changes in a periodic manner during the experiment.

modulated temperature (MT…), adj.

Applied to the technique name to indicate that a temperature modulation has been applied to the temperature program.

  • Note 1:

    As an example, a DSC experiment carried out with a modulated temperature program would be modulated temperature differential scanning calorimetry (MT-DSC).

  • Note 2:

    Other modulated techniques are possible, such as modulated force TMA, modulated rate SCTA, etc.

  • Note 3:

    The prefix TM is occasionally used instead, but not recommended.

photo-, prefix

Indicates that the experiment involves the illumination of the sample or measures the amount of light emitted from a sample. Where possible, the wavelength range of the light should be specified.

sample, n.

The material under study during the entire experiment (starting material, intermediates, and final products) and its close atmosphere. This is equivalent to the thermodynamic system.

sample controlled, adj.

Applied to the technique to indicate that a property of the sample is used either continuously or discontinuously to control the sample heating. Without this term, it is assumed that the experiment is following a controlled-temperature program.

  • Note:

    The generic term for all TA techniques making use of such feedback is sample-controlled TA (SCTA), whereas specific names will be of the form sample-controlled TGA (SC-TGA), etc.

scan, n.

(Discouraged) A term used to describe the data produced from a thermal analysis experiment. More correct usage is a thermal analysis curve, or, for a specific technique thermogravimetric curve, etc.

scanning, adj.

Indicates that a specified experimental parameter, if not temperature, is changed in a controlled manner.

scanning calorimetry, n.

Techniques where heat is measured as a function of temperature.

simultaneous, adj.

Indicates the measurement of two or more properties of a single sample at the same time. Different from combined.

  • Note:

    A hyphen is used to separate the abbreviations of the techniques; for example, simultaneous measurement of mass and heat flow rate (thermogravimetric analysis and differential scanning calorimetry) would be TGA-DSC.

static, adj.

Indicates, especially in the mechanical analysis of materials, a constant parameter during the experiment. The opposite of dynamic.

stepwise, adj.

Indicates discrete, discontinuous changes in an experimental parameter, e.g., force, temperature, etc.

tan δ, n.

The dimensionless ratio of energy lost to energy returned during one cycle of a periodic process. For example, tan δ = E″/E′, in DMA.

temperature-programmed desorption (TPD), n.

EGA using an inert atmosphere or vacuum, in the absence of sample decomposition.

temperature-programmed oxidation (TPO), n.

Experiment using an oxidising atmosphere, usually oxygen. Oxidation is monitored by any appropriate technique (EGA, TGA, gas sorption, etc.).

temperature-programmed reduction (TPR), n.

Experiment using a reducing atmosphere, usually hydrogen. Reduction is monitored by any appropriate technique (EGA, TGA, gas sorption, etc.).

thermal curve, n.

(Discouraged) Any graph of any combination of property, time, temperature derived from a thermal analysis technique.

  • Note:

    Thermal curve is a loose abbreviation of the more correct term thermoanalytical curve.

thermally stimulated current (TSC), n.

Electrical current observed during heating and caused by the thermally initiated relaxation of the frozen-in electrical polarization of a sample.

  • Note 1:

    By extension, the same name and abbreviation (TSC) are given to the thermal analysis technique based on the measurement of this current.

  • Note 2:

    See also thermally stimulated depolarization.

thermally stimulated depolarization, n.

Relaxation of frozen-in electrical polarization caused by a temperature increase.

  • Note:

    The effect is measured through the thermally stimulated current.

thermo-, prefix

Indicating the use of changing temperature during the experiment, when in the name of a thermal analysis technique.

thermoacoustimetry, n.

A technique whereby the characteristics of sound waves passing through the sample are measured.

thermoanalytical, adj.

Of, or pertaining to, thermal analysis.

thermodiffractometry, n.

A technique where the X-ray diffraction of the sample is measured.

thermodilatometry (TD), n.

A technique where one or more dimensions of the sample are measured under negligible load.

thermogravimetric analysis (TGA), n.

A technique where the mass of the sample is measured, also known as thermogravimetry.

thermogravimetry (TG), n.

See thermogravimetric analysis.

thermoluminescence, n.

A technique where light emission from the sample is measured.

thermomagnetometry, n.

A technique where a magnetic property of the sample is measured.

thermomanometry, n.

A technique where the gas pressure is measured.

thermomechanical analysis (TMA), n.

A technique where the deformation of the sample is measured under constant load.

thermomicroscopy, n.

A technique where the optical properties of the sample are observed and measured through a microscope.

thermoptometry, n.

A technique where the optical properties of a sample are measured.

thermosonimetry, n.

A technique where the sound emitted by the sample is measured.

thermospectrometry, n.

A group of techniques where a spectrum of the sample is measured.

torsional braid analysis (TBA), n.

A dynamic mechanical analysis technique where the sample is supported on a braid.

6 Reporting experimental data

For the experimental conditions to be fulfilled and reported, the reader is referred to the specific guidelines given in the ICTAC publications [1, 2], which are reproduced and progressively updated and complemented on the ICTAC website [www.ictac.org].

For reporting uncertainties, it is recommended to follow the guidelines published by the Joint Committee for Guides in Metrology [3, 4].

For the conventions on quantities, units and symbols to be used when reporting any work in thermal analysis, the reader is referred to IUPAC recommendations, especially the “Green Book” Quantities, Units and Symbols in Physical Chemistry [5].

7 Symbols used in thermal analysis

7.1 Symbols describing specific events or materials

  • In general, symbols for physical quantities should be in italic type, or, if vectors, in bold italic type.

  • The symbols for units do not take plural.

  • Subscripts should generally be restricted to single letters.

  • If the subscript relates to an object or property, it should be a CAPITAL letter:

    • m S = mass of sample S

    • T R = temperature of reference R

    • T C= Curie temperature

  • If the subscript refers to a phenomenon, it should be lower case:

    • T fus = melting temperature

    • T g = glass transition temperature

  • If the subscript refers to a specific event, time or point, it should be lower case or figures:

    • T i = initial temperature

    • m f = final mass

    • T p = peak temperature

    • t 1/2 = half-life of the reaction

  • Changes in extensive thermodynamic quantities X due to an event y should be represented by ΔyX:

    • ΔvapH= enthalpy of vaporization

    • ΔrG= Gibbs energy of reaction

  • Symbols for the physical state of the material should be put in brackets after the formula symbol:

    • ΔvapH = H(g) – H(l)

8 Overview and historical matters

This document is concerned with providing definitions of common terms that are used by thermal analysts to report, present, and explain their work.

The ICTAC Nomenclature Committee was initiated in 1965 under the guidance of Robert Mackenzie and with the secretarial expertise of Cyril Keattch. This document acknowledges the debt to previous members of the Committee under their succeeding Chairs, including John Sharp (1984–1988), Ed Gimzewski (1988–1992), and Wolfgang Hemminger (1992–2001), who continued the discussions and published their findings as listed in the references [6–16].

The task of the current committee has been to rationalise the work of all preceding committees and to deliver a document that covers current practice in thermal analysis that can be accepted internationally.

Thanks are due to recent members of the Nomenclature Committee listed for their contributions to the deliberations and to others for the advice received.

Recent members of the ICTAC Nomenclature Committee are as follows:

R. Blaine (2001–2006); D. Burlett (2001–2006); E. Charsley (2001–2006); V. Fernandez (2001–2006); P. C. Gravelle (1992–2001); B. O. Haglund (1992–2001); P. Haines (1997–2006, Secretary, 2003–2006); W. Hemminger (Chair, 1992–2001); G. Hakvoort (1992–2001); T. Lever (Chair, 2001–2006); M. Odlyha (1991–2001); T. Osawa (2001–2006); D. Price (2001–2006, Secretary, 2001–2003); M. Reading (1991–2007); S. Sarge (1992–2001, Secretary, 2000–2001); J. Simon (1992–2001); F. Wilburn (1992–2006, Secretary, 1991–2000).

9 Membership of sponsoring body

Membership of the IUPAC Physical and Biophysical Chemistry Division Committee for the period 2012–2013 was as follows:

President: K. Yamanouchi (Japan), Vice President: R. Marquardt (France); Secretary: A. Wilson (USA); Past President: A. McQuillan (New Zealand); Titular Members: K. Bartok (Belgium); A. Friedler (Israel); A. Goodwin (USA); R. Guidelli (Italy); A. Russell (UK); J. Stohner (Switzerland); Associate Members: V. Barone (Italy); A. Császár (Hungary); V. Kukushkin (Russia); V. Mišković-Stanković (Serbia); Á. Mombrú Rodríguez (Uruguay); X. S. Zhao (China); National Representatives: K. Bhattacharyya (India); J. Cejka (Czech Republic); S. Hannongbua (Thailand); M. Koper (Netherlands); A. J. Mahmood (Bangladesh); O. Mamchenko (Ukraine); J. Mdoe (Tanzania); F. Quina (Brazil); N. Soon (Malaysia); V. Tomišić (Croatia).

Acknowledgments

This work was sponsored by the International Union of Pure and Applied Chemistry, through the International Confederation for Thermal Analysis and Calorimetry (ICTAC), an Associated Organization of IUPAC. The Recommendation received its final form with the help of the IUPAC Physical and Biophysical Chemistry Division and in particular Prof. Ron Weir whom we especially wish to thank.

References

  • [1]

    (a) G. Lombardi. For Better Thermal Analysis, 1st ed., ICTA, Rome (1977); (b) G. Lombardi. For Better Thermal Analysis, 2nd ed., ICTA, Rome (1980).Google Scholar

  • [2]

    J. O. Hill. For Better Thermal Analysis and Calorimetry, 3rd ed., ICTAC (1991).Google Scholar

  • [3]

    BIPM. International Vocabulary of Metrology – Basic and General Concepts and Associated Terms (VIM), 3rd ed., Bureau International des Poids et Mesures, Geneva (2002); JCGM 200:2012 at http://www.bipm.org/en/publications/guides/vim.

  • [4]

    BIPM. Guide for Expression of Uncertainty in Measurement (GUM), Bureau International des Poids et Mesures, Sèvres (2008); JCGM 100:2008 at www.bipm.org/en/publications/guides/gum.html.

  • [5]

    IUPAC. Quantities, Units and Symbols in Physical Chemistry, 3rd ed. (the “Green Book”). Prepared for publication by E. R. Cohen, T. Cvitaš, J. G. Frey, B. Holmström, K. Kuchitsu, R. Marquardt, I. Mills, F. Pavese, M. Quack, J. Stohner, H. L. Strauss, M. Takami, A. J. Thor, RSC Publishing, Cambridge, UK (2007).Google Scholar

  • [6]

    R. C. Mackenzie. Talanta16, 1227 (1969).Google Scholar

  • [7]

    R. C. Mackenzie, C. J. Keattch, D. Dollimore, J. A. Forrester, A. A. Hodgson, J. P. Redfern. Talanta19, 1079 (1972).Google Scholar

  • [8]

    H. W. Thompson. Pure Appl. Chem. 37, 439 (1974).Google Scholar

  • [9]

    R. C. Mackenzie, C. J. Keattch, T. Daniels, D. Dollimore, J. A. Forrester, J. P. Redfern, J. H. Sharp. Thermochim. Acta12, 105 (1975).Google Scholar

  • [10]

    R. C. Mackenzie. Thermochim. Acta28, 1 (1979).Google Scholar

  • [11]

    G. G. Guilbault. Pure Appl. Chem. 52, 2385 (1980).Google Scholar

  • [12]

    R. C. Mackenzie. Thermochim Acta46, 333 (1981).CrossrefGoogle Scholar

  • [13]

    R. C. Mackenzie. Pure Appl. Chem. 57, 1737 (1985).Google Scholar

  • [14]

    J. H. Sharp. Thermochim. Acta104, 395 (1986).Google Scholar

  • [15]

    R. C. Mackenzie. In Treatise on Analytical Chemistry, P. J. Elving (Ed.), Part 1, Vol. 12, p. 1, John Wiley, New York (1983).Google Scholar

  • [16]

    W. Hemminger, S. M. Sarge. Handbook of Thermal Analysis and Calorimetry, Vol. 1, M. E. Brown (Ed.), Chap. 1, Elsevier, Amsterdam (1998).Google Scholar

Note: Republication or reproduction of this report or its storage and/or dissemination by electronic means is permitted without the need for formal IUPAC permission on condition that an acknowledgment, with full reference to the source, along with use of the copyright symbol ©, the name IUPAC, and the year of publication, are prominently visible. Publication of a translation into another language is subject to the additional condition of prior approval from the relevant IUPAC National Adhering Organization.

About the article

Corresponding author: Jean Rouquerol, Aix-Marseille Université-CNRS, Laboratoire MADIREL, Marseille, France, e-mail: jean.rouquerol@univ-amu.fr; jean.rouquerol@wanadoo.fr


Published Online: 2014-03-19

Published in Print: 2014-04-17


Citation Information: Pure and Applied Chemistry, Volume 86, Issue 4, Pages 545–553, ISSN (Online) 1365-3075, ISSN (Print) 0033-4545, DOI: https://doi.org/10.1515/pac-2012-0609.

Export Citation

©2014 by IUPAC & De Gruyter Berlin/Boston.Get Permission

Citing Articles

Here you can find all Crossref-listed publications in which this article is cited. If you would like to receive automatic email messages as soon as this article is cited in other publications, simply activate the “Citation Alert” on the top of this page.

[1]
Qiang Xie, Zhenzhong Zhang, Luyao Zhang, Yong Xie, Wei Liu, and Houhe Chen
Reaction Kinetics, Mechanisms and Catalysis, 2019
[2]
Milan Drábik
Pure and Applied Chemistry, 2017, Volume 89, Number 4, Page 451
[5]
Sha-Sha Wang, Rui-Kang Huang, Xiao-Xian Chen, Wei-Jian Xu, Wei-Xiong Zhang, and Xiao-Ming Chen
Crystal Growth & Design, 2019, Volume 19, Number 2, Page 1111
[6]
Ewa Ropelewska, Piotr Zapotoczny, Kamila Sabina Bożek, and Krystyna Żuk-Gołaszewska
Journal of Consumer Protection and Food Safety, 2018
[7]
A.P.G. Ferreira, B.V. Pinto, and É.T.G. Cavalheiro
Journal of Analytical and Applied Pyrolysis, 2018
[8]
V.S. Osipchik, Yu.V. Olikhova, L.Kh. Nguen, G.A. Lushcheikin, and V.M. Aristov
International Polymer Science and Technology, 2018, Volume 45, Number 6, Page 269
[9]
Ewa Ropelewska, Krzysztof J. Jankowski, Piotr Zapotoczny, and Bożena Bogucka
Zemdirbyste-Agriculture, 2018, Volume 105, Number 3, Page 257
[10]
Monique Barreto Santos, Bernardo de Sá Costa, and Edwin Elard Garcia Rojas
Ciência Rural, 2016, Volume 46, Number 8, Page 1491
[11]
Marta Díaz, Juan Antonio Palop, Carmen Sanmartín, and Elena Lizarraga
Journal of Thermal Analysis and Calorimetry, 2017, Volume 127, Number 2, Page 1663
[12]
Liang Wang, Gábor Várhegyi, Øyvind Skreiberg, Tian Li, Morten Grønli, and Michael J. Antal
Energy & Fuels, 2016, Volume 30, Number 4, Page 3186
[13]
R. C. Gallo, A. P. G. Ferreira, R. E. A. Castro, and E. T. G. Cavalheiro
Journal of Thermal Analysis and Calorimetry, 2016, Volume 123, Number 3, Page 2307
[14]
Małgorzata Labus, Krzysztof Labus, and Petr Bujok
Journal of Petroleum Science and Engineering, 2015, Volume 127, Page 482
[15]
Pedro Henrique O. Amorim, Ana Paula Garcia Ferreira, Luis Carlos M. Machado, Priscila Cervini, and Éder Tadeu Gomes Cavalheiro
Journal of Thermal Analysis and Calorimetry, 2015, Volume 120, Number 1, Page 1035

Comments (0)

Please log in or register to comment.
Log in