Torque motors are designed to operate as static machines and at low speeds [1, 2]. They are characterized by high nominal torques, characterised by large dimensions and precise workmanship. Since they operate in positioning systems, without transmission gear, there is no mechanical backlash. A shortcoming of these motors is a considerable cogging torque  associated with a large number of permanent magnets located on the rotor [3, 4]. Our paper deals with minimization of the cogging torque. The impact of asymmetry in magnet distribution on the cogging torque for a 12-pole torque motor whose stator has 18 slots is analyzed.
2 Methods of minimizing of a cogging torque
The methods to minimize the cogging torque that are most frequently used can be counted as:
The use of magnetic wedges,
The application of the pitch of the stator cribs,
The application of the pitch of the permanent magnet rotor,
The application of staves in stator teeth,
The asymmetry of staggered magnets on the periphery of the rotor.
One of the most popular is to use a pitch of the stator crib or the pitch of the permanent magnets . Almost complete elimination of the cogging torque is possible when employing a continuous pitch of stator crevices as well as the continuous bevel of the magnets. The realization of the continuous bevel considerably complicates the manufacturing process. The cost of production is greatly increased by the cumbersome shape of the magnets and difficulties with the technology of magnetizing. Therefore, while this method is used for individual solutions it is not suitable for mass production.
Another method of limiting the cogging torque is to create cutouts on the surface of the stator teeth. The aim of those extra cuts is to imitate the openings of creches. The width of the cuts is identical to the actual width of the stator crevice and the distribution is symmetrical. Thanks to this method there is a significant limitation of the maximum value of the cogging torque. In order to be effective, this technique needs to consider the number of cutouts in the stator teeth to the number of cogging moments that occur during the rotor rotation by the crest level. Additionally, it should be noted that the amplitude of the fundamental harmonic is greater than the amplitude of the remaining harmonics.
3 Evaluation of the cogging torque
3.1 Symmetrical distribution of the magnets
The asymmetry of the distribution of magnets on the rotor is applied here as the method to minimise the cogging torque. Initially, a constant angular velocity of the magnet and the same size gap between twelve magnets (Figure 1) were assumed. Then, maintaining the dimensions of the magnets, the size of one gap was changed while the other gaps remained equal. Under these conditions, the influence of the width of the single gap between magnets on the cogging torque was tested. Due to the considerable length of the machine in relation to the diameter calculations were performed using a 2D model . The simulation model was developed, and field calculations were carried out in the FEMM 4.2 . For the adopted magnetic circuit, the size of one gap was changed every 0,1°. The width of gap for which the cogging torque takes the minimum value was determined.
4 Distribution of the magnetic induction in the gap
For the calculation of magnetic induction in the gap, the FEMM 4.2[9, 10] finite element method (FEM) program was used. This takes into account the saturation of the respective elements of the magnetic circuit, the characteristics of magnetization of the ferromagnetic elements and the complex shapes of the circuit.
The distribution of the magnetic induction in the air gap for the symmetrical distribution of the magnets is repetitive in full rotation of the rotor.
Figure 5 shows the distribution of induction in the gap in the case of symmetrical distribution of magnets on the rotor. Fixed magnets have been distributed on the rotor at intervals of 30°.
For the asymmetrical distribution of magnets, there is a difference in the distribution of magnetic induction in the gap. The indentation chart in the slot has a significantly smaller amplitude in the full rotation of the motor. The distance between N-1 magnets was reduced by 2.5°, which increased the distance between the two magnets. The decay of the induction in the gap shows a significant decrease in the induction, and its rapid increase at the large gap between the magnets.
Figure 6 presents the magnetic induction in the air gap with respect to the shaft position.
For the calculation and determination of the smallest cogging torque, the method of minimizing the optimization of the engagement torque has been utilized, by applying the asymmetry of the permanent magnets to the rotor of the torque motor. The smallest cogging moment was determined by an empirical method. By changing the spacing of the magnets at 0.5°, the distance between the two magnets is increased. However, the distance between the N-1 magnets remained the same. A summary of the results is shown on Figure 7.
As it is presented in the attached chart, the maximum value of the cogging torque with the correct selection of the magnets is decreased in value four times. When the spacing between two magnets is too great, the value of the cogging torque increases.
Figure 8 shows that the value of the cogging torque depends strongly on small asymmetries in the distribution of magnets.
The cogging torque minimized by this method is four times smaller than the one observed for conditions of symmetry. The nominal torque of the machine is practically unchanged. With an asymmetric magnetic circuit, the rotor should be balanced despite the low speed of the motor.
The mesh elements impact on the accuracy of cogging torque determined by FEMM 4.2, and the value of the angle of rotation for subsequent calculations, and the highest number of grid points should be placed in the air gap. Too few grid elements and a large jump resulted in significant inaccuracies and shifts in results. The accuracy of calculations and the significance of the aforementioned conditions can be seen by comparing the values of Figures 7 and 8. These values, however, slightly differ from each other.
Chapman S. J., Electric machinery Fundamentals, New York: McGraw-Hill, 2012. Google Scholar
Gieras J., Wing M., Permanent Magnet Motor Technology, design and applications, Marcel Dekker, 2002. Google Scholar
Goryca Z., Malinowski M., Pakosz A., Wielobiegunowa maszyna z magnesami trwałymi o zredukowanym momencie zaczepowym, Patent nr 218930. Google Scholar
Goryca Z., Metoda minimalizacji momentu zaczepowego w wielobiegunowych maszynach z magnesami trwałymi, Wiadomości Elektrotechniczne, 2013, 12, 22-23. Google Scholar
Bernatt J., Obwody elektryczne i magnetyczne maszyn elektrycznych wzbudzanych magnesami trwałymi, Komel, Katowice, 2010.Google Scholar
Zarko D., Ban D., and Lipo T. A., Analytical solution for cogging torque in surface permanent-magnet motors using conformal mapping IEEE Trans. Magn., 2008, 44, 1, 52-65. Google Scholar
Goryca Z., Korkosz M., Mazur D., Rossa R., Ziółek M., Przydatność wybranych programów polowych do obliczania momentu zaczepowego wielobiegunowej maszyny z magnesami trwałymi, Zeszyty problemowe – Maszyny elektryczne, 2014, 3(103), 179-183 Google Scholar
Sooriyakumar G., Perryman R., Dodds S. J., Improved cogging torque calculation methods for surface mounted permanent magnet synchronous motors, In: Proc. Int. Uni. Power Engineering Conf., 2006, 2, 753-757. Google Scholar
Zhu Z. Q., Howe D., Bolte E., and Ackermann B., Instantaneous Magnetic Field Distribution in Brushless Permanent Magnet dc Motors, IEEE Transaction on magnetics, vol. 29, no. 1, January, 1993 Google Scholar
Srisiriwanna T, Konghirun M., A Study of Cogging Torque Reduction Methods in Brushless DC Motor, Ecti Transactions on Electrical eng., Electronics, and Communications vol.10, no.2 August, 2012 Google Scholar
Levin N., Orlova S., Pugachov V., Ose-Zala B., Jakobson E., Methods to Reduce the Cogging Torque in Permanent Magnet Synchronous Machines, Elektronika ir Elektrotechnika, ISSN 1392-1215, vol. 19, no. 1, 2013 Web of ScienceGoogle Scholar
Goryca Z., Paduszyński K., Pakosz A., The influence of asymmetrical distribution of rotor’s magnets on the cogging torque of the multipolar machine, ISEF Łódź, 2017Google Scholar
About the article
Published Online: 2018-03-20
Citation Information: Open Physics, Volume 16, Issue 1, Pages 42–45, ISSN (Online) 2391-5471, DOI: https://doi.org/10.1515/phys-2018-0008.
© 2018 Z. Goryca et al., published by De Gruyter. This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 License. BY-NC-ND 4.0